lhrf9ug42293/r1-pf doc. no : qw0905- rev. : date : 14 - jul. a - 2007 data sheet lhrf9ug42293/r1-pf dual color led lamps ligitek electronics co.,ltd. property of ligitek only pb lead-free parts
directivity radiation note : 1.all dimension are in millimeter tolerance is 0.25mm unless otherwise noted. 2.specifications are subject to change without notice. lhrf9ug42293/r1-pf package dimensions part no. ligitek electronics co.,ltd. property of ligitek only page 1/6 18.0min 1.5 max 4.2 6.7 0.5 2.0min 2.54typ 1 2.0min 2.54typ 2 3 3.0 4.0 5.2 0.5 typ 1.cathode green 2.common anode 3.cathode red 2 1 3 9ug hrf
tstg -40 ~ +100 storage temperature lhrf9ug42293/r1-pf water clear note : 1.the forward voltage data did not including 0.1v testing tolerance. 2. the luminous intensity data did not including 15% testing tolerance. algainp green574202.6 1.710.0 5.030 typical electrical & optical characteristics (ta=25 ) part no spectral halfwidth nm dominant wave length dnm color emitted algainp red material lens 63020 viewing angle 2 1/2 (deg) forward voltage @20ma(v) luminous intensity @20ma(mcd) max. min. typ. min. 1.52.49.015 30 electrostatic discharge( * ) operating temperature forward current reverse current @5v peak forward current duty 1/10@10khz power dissipation absolute maximum ratings at ta=25 i fp 9060 ma -40 ~ +85 t opr ir pd75 esd a 10 v mw 75 2000 ratings parameter symbol i f 30 hrf unit ma 30 9ug ligitek electronics co.,ltd. property of ligitek only page2/6 static electricity or power surge will damage the led. use of a conductive wrist band or anti-electrosatic glove is recommended when handing these led. all devices, equipment and machinery must be properly grounded. * lhrf9ug42293/r1-pf part no.
1.0 f o r w a r d v o l t a g e @ 2 0 m a n o r m a l i z e @ 2 5 r e l a t i v e i n t e n s i t y @ 2 0 m a n o r m a l i z e @ 2 5 ambient temperature( ) ambient temperature( ) fig.5 relative intensity vs. wavelength -40 0.8 0.9 -20-02040 0.5 100 80 600 0 -20 -402040100 6080 ligitek electronics co.,ltd. property of ligitek only fig.2 relative intensity vs. forward current 100 forward current(ma) fig.4 relative intensity vs. temperature 3.0 f o r w a r d c u r r e n t ( m a ) forward voltage(v) fig.3 forward voltage vs. temperature 1.0 1.1 1.2 1.0 1.0 0.1 10 100 1.52.0 3.0 2.0 1.5 2.5 2.5 2.0 1.5 1.0 0.5 0 r e l a t i v e i n t e n s i t y n o r m a l i z e @ 2 0 m a 2.53.010 1.0 typical electro-optical characteristics curve fig.1 forward current vs. forward voltage hrf chip 1000 3.5 1000 650700 550600 wavelength (nm) 1.0 0.5 r e l a t i v e i n t e n s i t y @ 2 0 m a 0 page 3/6 lhrf9ug42293/r1-pf part no.
fig.3 forward voltage vs. temperature ambient temperature( ) f o r w a r d v o l t a g e @ 2 0 m a n o r m a l i z @ 2 5 fig.4 relative intensity vs. temperature ambient temperature( ) r e l a t i v e i n t e n s i t y @ 2 0 m a n o r m a l i z e @ 2 5 typical electro-optical characteristics curve forward voltage(v) fig.1 forward current vs. forward voltage f o r w a r d c u r r e n t ( m a ) forward current(ma) fig.2 relative intensity vs. forward current r e l a t i v e i n t e n s i t y n o r m a l i z e @ 2 0 m a ligitek electronics co.,ltd. property of ligitek only 1.0 0.1 1.0 10 100 1000 1.0101001000 0 0.5 2.03.04.05.0 0.8 40 -20 -4080100 60 0 0.5 1.0 1.5 2.0 0.9 1.2 1.0 1.1 1.0 1.5 2.0 2.5 2.5 3.0 20 0 20 -400 -2080 4060100 3.0 9ug chip wavelength (nm) r e l a t i v e i n t e n s i t y @ 2 0 m a 0 500 0.5 1.0 550 600 650 fig.5 relative intensity vs. wavelength page 4/6 lhrf9ug42293/r1-pf part no.
5 /sec max 60 seconds max 25 2 /sec max 0 0 preheat 50 100 120 150 time(sec) dip soldering preheat: 120 c max preheat time: 60seconds max ramp-up 2 c/sec(max) ramp-down:-5 c/sec(max) solder bath:260 c max dipping time:3 seconds max distance:2mm min(from solder joint to body) 2.wave soldering profile 260 temp( c) 260 c3sec max soldering condition(pb-free) 1.iron: soldering iron:30w max temperature 350 c max soldering time:3 seconds max(one time only) distance:2mm min(from solder joint to body) ligitek electronics co.,ltd. property of ligitek only page 5/6 lhrf9ug42293/r1-pf part no. note:1.wave solder should not be made more than one time. 2.you can just only select one of the soldering conditions as above.
1.ta=65 5 2.rh=90%~95% 3.t=240hrs 2hrs 1.t.sol=230 5 2.dwell time=5 1sec this test intended to see soldering well performed or not. solderability test solder resistance test thermal shock test this test intended to determine the thermal characteristic resistance of the device to sudden exposures at extreme changes in temperature when soldering the lead wire. 1.t.sol=260 5 2.dwell time= 10 1sec. the purpose of this is the resistance of the device to sudden extreme changes in high and low temperature. 1.ta=105 5 &-40 5 (10min) (10min) 2.total 10 cycles mil-std-202: 208d mil-std-750: 2026 mil-std-883: 2003 jis c 7021: a-2 mil-std-202: 210a mil-std-750: 2031 jis c 7021: a-1 mil-std-202: 107d mil-std-750: 1051 mil-std-883: 1011 high temperature high humidity test low temperature storage test high temperature storage test the purpose of this is the resistance of the device which is laid under condition of low temperature for hours. the purpose of this test is the resistance of the device under tropical for hours. 1.ta=-40 5 2.t=1000 hrs (-24hrs, +72hrs) the purpose of this is the resistance of the device which is laid under condition of high temperature for hours. 1.ta=105 5 2.t=1000 hrs (-24hrs, +72hrs) reliability test: operating life test test item this test is conducted for the purpose of detemining the resistance of a part in electrical and themal stressed. 1.under room temperature 2.if=20ma 3.t=1000 hrs (-24hrs, +72hrs) test condition description mil-std-202:103b jis c 7021: b-11 jis c 7021: b-12 mil-std-883:1008 jis c 7021: b-10 mil-std-750: 1026 mil-std-883: 1005 jis c 7021: b-1 reference standard ligitek electronics co.,ltd. property of ligitek only page 6/6 lhrf9ug42293/r1-pf part no.
|
